Common Problems and solutions in Plumber Singapore

Water Leakage from Faucet

Here are the steps to resolve water leakage from a faucet:

Turn off the water supply: The first step is to turn off the water supply to the affected faucet. This can usually be done by turning the shut-off valve located under the sink or near the main water supply.
Disassemble the faucet: Using a screwdriver, remove the faucet handle and any other components that cover the faucet.
Inspect the components: Check the faucet’s components, including the rubber washers, O-rings, and valve seats for signs of wear and tear or damage. These are the most common causes of faucet leaks.
Replace worn components: If you find any damaged or worn components, replace them with new ones. You can purchase replacement parts from a hardware store or plumbing supply store.
Reassemble the faucet: Once you have replaced any worn components, reassemble the faucet in the reverse order that you disassembled it.
Turn on the water supply: Finally, turn on the water supply and check the faucet for leaks. If the faucet is still leaking, you may need to replace the entire faucet or seek the assistance of a professional plumber.

Remember, fixing a leaking faucet as soon as possible can save water and reduce your water bill, so it’s important to address any leaks promptly.

Toilet Bowl Issues

Here are the steps to resolve water leakage from a toilet bowl:

Identify the source of the leak: First, you need to identify the source of the leak. Check if the leak is coming from the base of the toilet or if it’s coming from the water supply line or tank.
Tighten bolts and nuts: If the leak is coming from the base of the toilet, it may be due to loose bolts or nuts that secure the toilet to the floor. Use a wrench to tighten these bolts and nuts.
Replace wax ring: If tightening the bolts and nuts doesn’t stop the leak, the wax ring between the toilet and the floor may be damaged or worn out. Turn off the water supply to the toilet and drain the toilet bowl. Remove the toilet from the floor and replace the wax ring. Reinstall the toilet and turn the water supply back on.
Check tank components: If the leak is coming from the tank or supply line, check the components inside the tank, such as the flapper valve, fill valve, or flush valve. These components can wear out over time and cause leaks. Replace any damaged or worn out components.
Tighten connections: Check the water supply line connections for any loose connections or leaks. Tighten any loose connections and replace any damaged or worn out parts.
Seek professional help: If you are not comfortable performing any of these steps or if the leak persists, it’s best to seek the assistance of a professional plumber.

Remember, water leakage from a toilet bowl can waste a significant amount of water and increase your water bill, so it’s important to address any leaks as soon as possible.

Water leak from Storage Heater

Here are the steps to resolve water leakage from a water heater:

Turn off the power supply: The first step is to turn off the power supply to the water heater. This can be done by turning off the circuit breaker or switch that controls the heater.
Shut off the water supply: Next, turn off the water supply to the heater. This valve is usually located near the top of the heater or on the incoming water line.
Drain the water heater: Open a hot water faucet in your home to release pressure in the system. Then, attach a hose to the drain valve on the bottom of the water heater and drain the tank completely.
Check for leaks: Once the tank is drained, inspect the heater for any signs of leaks. Check the temperature and pressure relief valve, drain valve, and the tank itself for any visible signs of water.
Replace faulty components: If you identify any faulty components, such as a leaking valve, replace them with new ones. You can purchase replacement parts from a hardware store or plumbing supply store.
Refill and restart the heater: Once you have replaced any faulty components, close the drain valve and refill the tank with water. Turn on the water supply and power supply to the heater, and wait for the tank to refill and the heater to reheat the water.
Check for leaks again: Finally, check for any leaks again after the water heater has been refilled and reheated. If you still see any leaks, it’s best to seek the assistance of a professional plumber.

Remember, water leakage from a water heater can cause significant damage to your home, so it’s important to address any leaks as soon as possible.

Pipe Burst and Water Leak

Here are the steps to resolve water leakage from a pipe burst:

Turn off the water supply: The first step is to turn off the water supply to your home. This can usually be done by turning off the main water supply valve located near the water meter.
Drain the pipes: Open all the faucets in your home to drain any water remaining in the pipes. This will reduce the amount of water that will escape when you cut into the pipe.
Locate the burst pipe: The next step is to locate the burst pipe. Look for any visible signs of water damage, such as wet walls or ceilings.
Cut out the damaged section: Once you have located the burst pipe, use a hacksaw or pipe cutter to cut out the damaged section of the pipe. Cut at least 2 inches away from the damaged area.
Replace the damaged section: Measure the length of the removed section and purchase a replacement pipe of the same material and diameter. Use couplings or compression fittings to connect the new pipe to the existing pipes.
Seal the joints: Use Teflon tape or pipe sealant to seal the joints between the pipes and the fittings.
Turn the water supply back on: Once you have replaced the damaged section of the pipe and sealed the joints, turn the water supply back on and check for any leaks.

Remember, a burst pipe can cause significant damage to your home and personal property, so it’s important to address the issue as soon as possible. If you are not comfortable performing any of these steps or if the leak persists, it’s best to seek the assistance of a professional plumber.

Kitchen Tap leaking

Here are the steps to resolve water leakage from a kitchen tap:

Turn off the water supply: The first step is to turn off the water supply to the kitchen tap. This can usually be done by turning off the valve under the sink.
Close the drain: Close the drain in the sink so that no small parts fall down the drain.
Disassemble the tap: Use a wrench to loosen and remove the handle of the tap. This will give you access to the inner workings of the tap.
Inspect the O-ring and washer: Check the O-ring and washer inside the tap for any signs of wear and tear or damage. These parts are usually the cause of leaks in a tap.
Replace the damaged parts: If you find any damaged parts, replace them with new ones. You can purchase replacement parts from a hardware store or plumbing supply store.
Reassemble the tap: Once you have replaced any damaged parts, reassemble the tap in the reverse order that you disassembled it.
Turn the water supply back on: Turn the water supply back on and check for any leaks.

Remember, a leaky kitchen tap can waste a lot of water and increase your water bill, so it’s important to address the issue as soon as possible. If you are not comfortable performing any of these steps or if the leak persists, it’s best to seek the assistance of a professional plumber.

Choke issues

Here are the steps to resolve a pipe choke:

Identify the location of the choke: First, identify the location of the choke. This can be done by observing which fixtures are affected, such as slow draining sinks or toilets.
Use a plunger: If the choke is in a sink or toilet, use a plunger to try and dislodge the blockage. Make sure there is enough water in the fixture to cover the plunger and create a seal. Pump the plunger up and down vigorously several times.
Use a plumbing snake: If the plunger does not work, try using a plumbing snake. Insert the snake into the drain and turn the handle to move it through the pipe. This will help break up any blockages.
Try a drain cleaner: If the plunger and plumbing snake do not work, try using a drain cleaner. There are many different types of drain cleaners available, but make sure to follow the instructions carefully and use protective gloves and eyewear.
Call a professional plumber: If none of the above methods work, it’s time to call a professional plumber. A plumber will have specialized tools and equipment to locate and remove the blockage.

It’s important to address a pipe choke as soon as possible to avoid any further damage or blockages in your plumbing system. Regular maintenance, such as flushing drains with hot water and avoiding flushing non-biodegradable items down the toilet, can also help prevent future chokes.

Floor Trap Issues

Here are the steps to resolve floor trap issues:

Remove any debris: If the floor trap is clogged, start by removing any debris or hair that may be blocking the trap. You can use a pair of gloves and a small tool like a wire brush or pliers to remove the debris.
Use a plunger: After removing any debris, try using a plunger to dislodge any remaining blockages. Make sure to create a tight seal between the plunger and the floor trap and pump it up and down several times.
Use a plumbing snake: If the plunger doesn’t work, try using a plumbing snake to remove any blockages that may be further down the pipe.
Check the water seal: Make sure the water seal in the floor trap is working properly. The water seal is a small amount of water that sits in the bottom of the trap to prevent odors from coming up through the drain. If the water seal is missing or damaged, it can cause unpleasant odors in your home.
Call a professional plumber: If the above methods do not resolve the issue, it’s time to call a professional plumber. A plumber will have specialized tools and equipment to locate and remove any blockages or repair any damage to the floor trap.

Regular maintenance, such as cleaning the floor trap and flushing it with hot water, can also help prevent floor trap issues in the future.